jlpoole/LilyGo-LoRa-Series
1
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity Actions 1

Update examples

Browse source
This commit is contained in:
lewisxhe 2025-12-31 15:01:44 +08:00
commit 3973b751be
4 changed files with 234 additions and 76 deletions
Download patch file Download diff file Expand all files Collapse all files

94
examples/RadioLibExamples/Receive_Interrupt/Receive_Interrupt.ino
View file

@ -94,30 +94,60 @@ SX1268 radio = new Module(RADIO_CS_PIN, RADIO_DIO1_PIN, RADIO_RST_PIN, RADIO_BUS
#elif defined(USING_LR1121)
// The maximum power of LR1121 2.4G band can only be set to 13 dBm
// #ifndef CONFIG_RADIO_FREQ
// #define CONFIG_RADIO_FREQ 2450.0
// #endif
// #ifndef CONFIG_RADIO_OUTPUT_POWER
// #define CONFIG_RADIO_OUTPUT_POWER 13
// #endif
// #ifndef CONFIG_RADIO_BW
// #define CONFIG_RADIO_BW 125.0
// #endif
/*
* Important: LR1121 PA Version
*
* The 2.4G version does not have a power amplifier (PA). The permissible power setting is 13dBm.
*
* If it is a version with a built-in PA, please do not exceed 0dBm in the maximum power setting.
* This is because a power amplifier has been added to the RF front-end; setting it to 0dBm will achieve an output power of 22dBm.
* Setting it to more than 1dBm may damage the PA.
*
* */
#define CONFIG_RADIO_FREQ 2450.0
#define CONFIG_RADIO_OUTPUT_POWER LILYGO_RADIO_2G4_TX_POWER_LIMIT
#define CONFIG_RADIO_BW 125.0
// The maximum power of LR1121 Sub 1G band can only be set to 22 dBm
#ifndef CONFIG_RADIO_FREQ
#define CONFIG_RADIO_FREQ 868.0
#endif
#ifndef CONFIG_RADIO_OUTPUT_POWER
#define CONFIG_RADIO_OUTPUT_POWER 22
#endif
#ifndef CONFIG_RADIO_BW
#define CONFIG_RADIO_BW 125.0
#endif
// #define CONFIG_RADIO_FREQ 868.0
// #define CONFIG_RADIO_OUTPUT_POWER 22
// #define CONFIG_RADIO_BW 125.0
LR1121 radio = new Module(RADIO_CS_PIN, RADIO_DIO9_PIN, RADIO_RST_PIN, RADIO_BUSY_PIN);
#endif
#ifdef USING_LR1121PA
// LR1121 Version PA RF switch table
static const uint32_t pa_version_rf_switch_dio_pins[] = {
RADIOLIB_LR11X0_DIO5, RADIOLIB_LR11X0_DIO6, RADIOLIB_LR11X0_DIO7, RADIOLIB_LR11X0_DIO8, RADIOLIB_NC
};
static const Module::RfSwitchMode_t high_freq_switch_table[] = {
// mode DIO5 DIO6 DIO7 DIO8
{ LR11x0::MODE_STBY, { LOW, LOW, LOW, LOW} },
{ LR11x0::MODE_TX, { LOW, LOW, LOW, HIGH} },
{ LR11x0::MODE_RX, { LOW, LOW, HIGH, LOW} },
{ LR11x0::MODE_TX_HP, { LOW, LOW, HIGH, LOW} },
{ LR11x0::MODE_TX_HF, { LOW, LOW, HIGH, LOW} },
{ LR11x0::MODE_GNSS, { LOW, LOW, LOW, HIGH} },
{ LR11x0::MODE_WIFI, { LOW, LOW, LOW, HIGH} },
END_OF_MODE_TABLE,
};
static const Module::RfSwitchMode_t low_freq_switch_table[] = {
// mode DIO5 DIO6 DIO7 DIO8
{ LR11x0::MODE_STBY, { LOW, LOW, LOW, LOW} },
{ LR11x0::MODE_TX, { LOW, HIGH, LOW, LOW} },
{ LR11x0::MODE_RX, { HIGH, LOW, LOW, LOW} },
{ LR11x0::MODE_TX_HP, { LOW, HIGH, LOW, LOW} },
{ LR11x0::MODE_TX_HF, { LOW, LOW, LOW, LOW} },
{ LR11x0::MODE_GNSS, { LOW, LOW, LOW, LOW} },
{ LR11x0::MODE_WIFI, { LOW, LOW, LOW, LOW} },
END_OF_MODE_TABLE,
};
#endif /*USING_LR1121PA*/
#endif /*Radio define end*/
// flag to indicate that a packet was received
static volatile bool receivedFlag = false;
@ -230,7 +260,7 @@ void setup()
* SX1262 : Allowed values are in range from -9 to 22 dBm. This method is virtual to allow override from the SX1261 class.
* SX1268 : Allowed values are in range from -9 to 22 dBm.
* SX1280 : Allowed values are in range from -18 to 13 dBm. PA Version range : -18 ~ 3dBm
* LR1121 : Allowed values are in range from -17 to 22 dBm (high-power PA) or -18 to 13 dBm (High-frequency PA)
* LR1121 : Allowed values are in range from -17 to 22 dBm (high-power PA) or -18 to 13 dBm (High-frequency PA), PA Version range : -9 ~ 0dBm
* * * */
if (radio.setOutputPower(CONFIG_RADIO_OUTPUT_POWER) == RADIOLIB_ERR_INVALID_OUTPUT_POWER) {
Serial.println(F("Selected output power is invalid for this module!"));
@ -269,14 +299,20 @@ void setup()
}
#if defined(USING_LR1121)
// LR1121
// set RF switch configuration for Wio WM1110
// Wio WM1110 uses DIO5 and DIO6 for RF switching
#if defined(USING_LR1121PA)
if (CONFIG_RADIO_FREQ < 2400) {
Serial.printf("LR1121 PA Version Using low frequency switch table for PA version\n");
radio.setRfSwitchTable(pa_version_rf_switch_dio_pins, low_freq_switch_table);
} else {
Serial.printf("LR1121 PA Version Using high frequency switch table for PA version\n");
radio.setRfSwitchTable(pa_version_rf_switch_dio_pins, high_freq_switch_table);
}
#else // Version without PA rf switch table
Serial.println("LR1121 without PA Version");
static const uint32_t rfswitch_dio_pins[] = {
RADIOLIB_LR11X0_DIO5, RADIOLIB_LR11X0_DIO6,
RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC
};
static const Module::RfSwitchMode_t rfswitch_table[] = {
// mode DIO5 DIO6
{ LR11x0::MODE_STBY, { LOW, LOW } },
@ -289,12 +325,12 @@ void setup()
END_OF_MODE_TABLE,
};
radio.setRfSwitchTable(rfswitch_dio_pins, rfswitch_table);
#endif /*USING_LR1121PA*/
// LR1121 TCXO Voltage 2.85~3.15V
radio.setTCXO(3.0);
#endif
#endif /*USING_LR1121*/
#ifdef USING_DIO2_AS_RF_SWITCH
#ifdef USING_SX1262
@ -351,12 +387,8 @@ void setup()
}
drawMain();
}
void loop()
{
// check if the flag is set

90
examples/RadioLibExamples/Transmit_Interrupt/Transmit_Interrupt.ino
View file

@ -89,30 +89,60 @@ SX1268 radio = new Module(RADIO_CS_PIN, RADIO_DIO1_PIN, RADIO_RST_PIN, RADIO_BUS
#elif defined(USING_LR1121)
// The maximum power of LR1121 2.4G band can only be set to 13 dBm
// #ifndef CONFIG_RADIO_FREQ
// #define CONFIG_RADIO_FREQ 2450.0
// #endif
// #ifndef CONFIG_RADIO_OUTPUT_POWER
// #define CONFIG_RADIO_OUTPUT_POWER 13
// #endif
// #ifndef CONFIG_RADIO_BW
// #define CONFIG_RADIO_BW 125.0
// #endif
/*
* Important: LR1121 PA Version
*
* The 2.4G version does not have a power amplifier (PA). The permissible power setting is 13dBm.
*
* If it is a version with a built-in PA, please do not exceed 0dBm in the maximum power setting.
* This is because a power amplifier has been added to the RF front-end; setting it to 0dBm will achieve an output power of 22dBm.
* Setting it to more than 1dBm may damage the PA.
*
* */
#define CONFIG_RADIO_FREQ 2450.0
#define CONFIG_RADIO_OUTPUT_POWER LILYGO_RADIO_2G4_TX_POWER_LIMIT
#define CONFIG_RADIO_BW 125.0
// The maximum power of LR1121 Sub 1G band can only be set to 22 dBm
#ifndef CONFIG_RADIO_FREQ
#define CONFIG_RADIO_FREQ 868.0
#endif
#ifndef CONFIG_RADIO_OUTPUT_POWER
#define CONFIG_RADIO_OUTPUT_POWER 22
#endif
#ifndef CONFIG_RADIO_BW
#define CONFIG_RADIO_BW 125.0
#endif
// #define CONFIG_RADIO_FREQ 868.0
// #define CONFIG_RADIO_OUTPUT_POWER 22
// #define CONFIG_RADIO_BW 125.0
LR1121 radio = new Module(RADIO_CS_PIN, RADIO_DIO9_PIN, RADIO_RST_PIN, RADIO_BUSY_PIN);
#endif
#ifdef USING_LR1121PA
// LR1121 Version PA RF switch table
static const uint32_t pa_version_rf_switch_dio_pins[] = {
RADIOLIB_LR11X0_DIO5, RADIOLIB_LR11X0_DIO6, RADIOLIB_LR11X0_DIO7, RADIOLIB_LR11X0_DIO8, RADIOLIB_NC
};
static const Module::RfSwitchMode_t high_freq_switch_table[] = {
// mode DIO5 DIO6 DIO7 DIO8
{ LR11x0::MODE_STBY, { LOW, LOW, LOW, LOW} },
{ LR11x0::MODE_TX, { LOW, LOW, LOW, HIGH} },
{ LR11x0::MODE_RX, { LOW, LOW, HIGH, LOW} },
{ LR11x0::MODE_TX_HP, { LOW, LOW, HIGH, LOW} },
{ LR11x0::MODE_TX_HF, { LOW, LOW, HIGH, LOW} },
{ LR11x0::MODE_GNSS, { LOW, LOW, LOW, HIGH} },
{ LR11x0::MODE_WIFI, { LOW, LOW, LOW, HIGH} },
END_OF_MODE_TABLE,
};
static const Module::RfSwitchMode_t low_freq_switch_table[] = {
// mode DIO5 DIO6 DIO7 DIO8
{ LR11x0::MODE_STBY, { LOW, LOW, LOW, LOW} },
{ LR11x0::MODE_TX, { LOW, HIGH, LOW, LOW} },
{ LR11x0::MODE_RX, { HIGH, LOW, LOW, LOW} },
{ LR11x0::MODE_TX_HP, { LOW, HIGH, LOW, LOW} },
{ LR11x0::MODE_TX_HF, { LOW, LOW, LOW, LOW} },
{ LR11x0::MODE_GNSS, { LOW, LOW, LOW, LOW} },
{ LR11x0::MODE_WIFI, { LOW, LOW, LOW, LOW} },
END_OF_MODE_TABLE,
};
#endif /*USING_LR1121PA*/
#endif /*Radio define end*/
void drawMain();
@ -228,7 +258,7 @@ void setup()
* SX1262 : Allowed values are in range from -9 to 22 dBm. This method is virtual to allow override from the SX1261 class.
* SX1268 : Allowed values are in range from -9 to 22 dBm.
* SX1280 : Allowed values are in range from -18 to 13 dBm. PA Version range : -18 ~ 3dBm
* LR1121 : Allowed values are in range from -17 to 22 dBm (high-power PA) or -18 to 13 dBm (High-frequency PA)
* LR1121 : Allowed values are in range from -17 to 22 dBm (high-power PA) or -18 to 13 dBm (High-frequency PA), PA Version range : -9 ~ 0dBm
* * * */
if (radio.setOutputPower(CONFIG_RADIO_OUTPUT_POWER) == RADIOLIB_ERR_INVALID_OUTPUT_POWER) {
Serial.println(F("Selected output power is invalid for this module!"));
@ -267,14 +297,20 @@ void setup()
}
#if defined(USING_LR1121)
// LR1121
// set RF switch configuration for Wio WM1110
// Wio WM1110 uses DIO5 and DIO6 for RF switching
#if defined(USING_LR1121PA)
if (CONFIG_RADIO_FREQ < 2400) {
Serial.printf("LR1121 PA Version Using low frequency switch table for PA version\n");
radio.setRfSwitchTable(pa_version_rf_switch_dio_pins, low_freq_switch_table);
} else {
Serial.printf("LR1121 PA Version Using high frequency switch table for PA version\n");
radio.setRfSwitchTable(pa_version_rf_switch_dio_pins, high_freq_switch_table);
}
#else // Version without PA rf switch table
Serial.println("LR1121 without PA Version");
static const uint32_t rfswitch_dio_pins[] = {
RADIOLIB_LR11X0_DIO5, RADIOLIB_LR11X0_DIO6,
RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC
};
static const Module::RfSwitchMode_t rfswitch_table[] = {
// mode DIO5 DIO6
{ LR11x0::MODE_STBY, { LOW, LOW } },
@ -287,10 +323,12 @@ void setup()
END_OF_MODE_TABLE,
};
radio.setRfSwitchTable(rfswitch_dio_pins, rfswitch_table);
#endif /*USING_LR1121PA*/
// LR1121 TCXO Voltage 2.85~3.15V
radio.setTCXO(3.0);
#endif
#endif /*USING_LR1121*/
#ifdef USING_DIO2_AS_RF_SWITCH
#ifdef USING_SX1262

114
examples/T3S3Factory/T3S3Factory.ino
View file

@ -51,6 +51,16 @@ SX1262 radio = new Module(RADIO_CS_PIN, RADIO_DIO1_PIN, RADIO_RST_PIN, RADIO_BUS
SX1280 radio = new Module(RADIO_CS_PIN, RADIO_DIO1_PIN, RADIO_RST_PIN, RADIO_BUSY_PIN);
#elif defined(USING_SX1280PA)
/*
* Important: SX1280 PA Version
* The 2.4G version does not have a power amplifier (PA). The permissible power setting is 13dBm.
* If it is a version with a built-in PA, do not set the maximum power beyond 3dBm.
* This is because a power amplifier is added to the RF front end; setting it to 3dBm will achieve an output power of 22dBm.
* Setting it beyond 3dBm may damage the PA.
*/
#define CONFIG_RADIO_FREQ 2400.0
#define CONFIG_RADIO_OUTPUT_POWER 3 // PA Version power range : -18 ~ 3dBm
#define CONFIG_RADIO_BW 203.125
@ -58,18 +68,61 @@ SX1280 radio = new Module(RADIO_CS_PIN, RADIO_DIO1_PIN, RADIO_RST_PIN, RADIO_BUS
#elif defined(USING_LR1121)
// The maximum power of LR1121 2.4G band can only be set to 13 dBm
// #define CONFIG_RADIO_FREQ 2450.0
// #define CONFIG_RADIO_OUTPUT_POWER 13
// #define CONFIG_RADIO_BW 125.0
/*
* Important: LR1121 PA Version
*
* The 2.4G version does not have a power amplifier (PA). The permissible power setting is 13dBm.
*
* If it is a version with a built-in PA, please do not exceed 0dBm in the maximum power setting.
* This is because a power amplifier has been added to the RF front-end; setting it to 0dBm will achieve an output power of 22dBm.
* Setting it to more than 1dBm may damage the PA.
*
* */
// The maximum power of LR1121 Sub 1G band can only be set to 22 dBm
#define CONFIG_RADIO_FREQ 868.0
#define CONFIG_RADIO_OUTPUT_POWER 22
#define CONFIG_RADIO_FREQ 2450.0
#define CONFIG_RADIO_OUTPUT_POWER LILYGO_RADIO_2G4_TX_POWER_LIMIT
#define CONFIG_RADIO_BW 125.0
// The maximum power of LR1121 Sub 1G band can only be set to 22 dBm
// #define CONFIG_RADIO_FREQ 868.0
// #define CONFIG_RADIO_OUTPUT_POWER 22
// #define CONFIG_RADIO_BW 125.0
LR1121 radio = new Module(RADIO_CS_PIN, RADIO_DIO9_PIN, RADIO_RST_PIN, RADIO_BUSY_PIN);
#endif
#ifdef USING_LR1121PA
// LR1121 Version PA RF switch table
static const uint32_t pa_version_rf_switch_dio_pins[] = {
RADIOLIB_LR11X0_DIO5, RADIOLIB_LR11X0_DIO6, RADIOLIB_LR11X0_DIO7, RADIOLIB_LR11X0_DIO8, RADIOLIB_NC
};
static const Module::RfSwitchMode_t high_freq_switch_table[] = {
// mode DIO5 DIO6 DIO7 DIO8
{ LR11x0::MODE_STBY, { LOW, LOW, LOW, LOW} },
{ LR11x0::MODE_TX, { LOW, LOW, LOW, HIGH} },
{ LR11x0::MODE_RX, { LOW, LOW, HIGH, LOW} },
{ LR11x0::MODE_TX_HP, { LOW, LOW, HIGH, LOW} },
{ LR11x0::MODE_TX_HF, { LOW, LOW, HIGH, LOW} },
{ LR11x0::MODE_GNSS, { LOW, LOW, LOW, HIGH} },
{ LR11x0::MODE_WIFI, { LOW, LOW, LOW, HIGH} },
END_OF_MODE_TABLE,
};
static const Module::RfSwitchMode_t low_freq_switch_table[] = {
// mode DIO5 DIO6 DIO7 DIO8
{ LR11x0::MODE_STBY, { LOW, LOW, LOW, LOW} },
{ LR11x0::MODE_TX, { LOW, HIGH, LOW, LOW} },
{ LR11x0::MODE_RX, { HIGH, LOW, LOW, LOW} },
{ LR11x0::MODE_TX_HP, { LOW, HIGH, LOW, LOW} },
{ LR11x0::MODE_TX_HF, { LOW, LOW, LOW, LOW} },
{ LR11x0::MODE_GNSS, { LOW, LOW, LOW, LOW} },
{ LR11x0::MODE_WIFI, { LOW, LOW, LOW, LOW} },
END_OF_MODE_TABLE,
};
#endif /*USING_LR1121PA*/
#endif /*Radio define end*/
enum TransmissionDirection {
LORA_NONE = 0,
@ -227,10 +280,19 @@ void changeFreq()
#if defined(USING_LR1121)
bool forceHighPower = false;
int8_t max_tx_power = 13;
int8_t max_tx_power = LILYGO_RADIO_2G4_TX_POWER_LIMIT;
if (current_freq < 2400) {
max_tx_power = 22;
forceHighPower = true;
#if defined(USING_LR1121PA)
Serial.printf("Using low frequency switch table for PA version\n");
radio.setRfSwitchTable(pa_version_rf_switch_dio_pins, low_freq_switch_table);
#endif /*USING_LR1121PA*/
} else {
#if defined(USING_LR1121PA)
Serial.printf("Using high frequency switch table for PA version\n");
radio.setRfSwitchTable(pa_version_rf_switch_dio_pins, high_freq_switch_table);
#endif /*USING_LR1121PA*/
}
if (radio.setOutputPower(max_tx_power, forceHighPower) == RADIOLIB_ERR_INVALID_OUTPUT_POWER) {
Serial.printf("Selected output power %d is invalid for this module!\n", max_tx_power);
@ -270,11 +332,18 @@ void handleEvent(AceButton *button, uint8_t eventType, uint8_t buttonState)
case 0:
break;
case 1:
#ifdef RADIO_TX_CW
Serial.println("Start transmit (CW)");
radio.standby();
delay(100);
radio.transmitDirect();
#else
Serial.println("Start transmit");
state = radio.transmit((uint8_t *)&transmissionCounter, 4);
if (state != RADIOLIB_ERR_NONE) {
Serial.println(F("[Radio] transmit packet failed!"));
}
#endif
break;
case 2:
Serial.println("Start receive");
@ -441,7 +510,7 @@ void setup()
* SX1262 : Allowed values are in range from -9 to 22 dBm. This method is virtual to allow override from the SX1261 class.
* SX1268 : Allowed values are in range from -9 to 22 dBm.
* SX1280 : Allowed values are in range from -18 to 13 dBm. PA Version range : -18 ~ 3dBm
* LR1121 : Allowed values are in range from -17 to 22 dBm (high-power PA) or -18 to 13 dBm (High-frequency PA)
* LR1121 : Allowed values are in range from -17 to 22 dBm (high-power PA) or -18 to 13 dBm (High-frequency PA), PA Version range : -9 ~ 0dBm
* * * */
if (radio.setOutputPower(CONFIG_RADIO_OUTPUT_POWER) == RADIOLIB_ERR_INVALID_OUTPUT_POWER) {
Serial.println(F("Selected output power is invalid for this module!"));
@ -481,14 +550,20 @@ void setup()
#if defined(USING_LR1121)
// LR1121
// set RF switch configuration for Wio WM1110
// Wio WM1110 uses DIO5 and DIO6 for RF switching
#if defined(USING_LR1121PA)
if (current_freq < 2400) {
Serial.printf("LR1121 PA Version Using low frequency switch table for PA version\n");
radio.setRfSwitchTable(pa_version_rf_switch_dio_pins, low_freq_switch_table);
} else {
Serial.printf("LR1121 PA Version Using high frequency switch table for PA version\n");
radio.setRfSwitchTable(pa_version_rf_switch_dio_pins, high_freq_switch_table);
}
#else // Version without PA rf switch table
Serial.println("LR1121 without PA Version");
static const uint32_t rfswitch_dio_pins[] = {
RADIOLIB_LR11X0_DIO5, RADIOLIB_LR11X0_DIO6,
RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC
};
static const Module::RfSwitchMode_t rfswitch_table[] = {
// mode DIO5 DIO6
{ LR11x0::MODE_STBY, { LOW, LOW } },
@ -501,11 +576,12 @@ void setup()
END_OF_MODE_TABLE,
};
radio.setRfSwitchTable(rfswitch_dio_pins, rfswitch_table);
#endif /*USING_LR1121PA*/
// LR1121 TCXO Voltage 2.85~3.15V
radio.setTCXO(3.0);
#endif
#endif /*USING_LR1121*/
// set the function that will be called
// when new packet is received
@ -533,6 +609,11 @@ void loop()
void radioTx(OLEDDisplay *display, OLEDDisplayUiState *state, int16_t x, int16_t y)
{
display->setTextAlignment(TEXT_ALIGN_LEFT);
#ifdef RADIO_TX_CW
display->drawString(0 + x, 0 + y, "Radio CW");
display->drawString(0 + x, 12 + y, "FREQ :" + String(current_freq));
#else
if (millis() - radioRunInterval > 1000) {
if (transmittedFlag) {
@ -579,11 +660,12 @@ void radioTx(OLEDDisplay *display, OLEDDisplayUiState *state, int16_t x, int16_t
radioRunInterval = millis();
}
display->drawString(0 + x, 0 + y, "Radio Tx");
display->drawString(0 + x, 12 + y, "FREQ :" + String(current_freq));
display->drawString(0 + x, 24 + y, "TX :" + String(transmissionCounter));
display->drawString(0 + x, 36 + y, "BW :" + String(CONFIG_RADIO_BW));
#endif
}

12
platformio.ini
View file

@ -42,6 +42,7 @@
; default_envs = T3_S3_V1_2_SX1280
; default_envs = T3_S3_V1_2_SX1280_PA
; default_envs = T3_S3_V1_2_LR1121
; default_envs = T3_S3_V1_2_LR1121_PA
; default_envs = T3_C6_SX1262
@ -137,12 +138,12 @@
; src_dir = examples/TBeamFactory
; T-Beam V1.2 / T-Beam S3 Supreme / T-Beam-1W / T-Beam-BPF factory example
src_dir = examples/Factory
; src_dir = examples/Factory
boards_dir = boards
[env]
platform = espressif32@6.9.0
platform = espressif32@6.12.0
framework = arduino
upload_speed = 921600
monitor_speed = 115200
@ -150,7 +151,6 @@ monitor_filters =
default
esp32_exception_decoder
[esp32_base]
build_flags =
${env.build_flags}
@ -287,6 +287,12 @@ board = t3_s3_v1_x
build_flags = ${esp32s3_base.build_flags}
-DT3_S3_V1_2_LR1121
[env:T3_S3_V1_2_LR1121_PA]
extends = env
board = t3_s3_v1_x
build_flags = ${esp32s3_base.build_flags}
-DT3_S3_V1_2_LR1121_PA
[env:T_MOTION]
platform = ststm32
framework = arduino