Update fw

firmware/GPS_Reset/README.MD

@@ -20,72 +20,12 @@
    | GPS_ reset.bin*           | [firmware](./GPS_%20reset.bin)          |
    | GPS_BasicNMEARead.bin*    | [firmware](./GPS_BasicNMEARead.bin)     |
 
-## How to Flash ?
-
-
-### Before burning firmware, please put the board into download mode and follow the steps below
-
- 1. Connect the board via the USB cable
- 2. Press and hold the **BOOT** button , While still pressing the **BOOT** button (If there is no **BOOT** button, you need to use wires to connect **GND** and **IO0** together.)
- 3. Press **RST** button
- 4. Release the **RST** button
- 5. Release the **BOOT** button (If there is no **BOOT** button, disconnect IO0 from GND.)
- 6. Upload sketch
- 7. Press the **RST** button to exit download mode
-
-
-
-### Use ESP Download Tool
-
-- Download [Flash_download_tool](https://www.espressif.com.cn/sites/default/files/tools/flash_download_tool_3.9.6_0.zip)
-
-![web_flasher](../images/esp_downloader.gif)
-
-* **Note that after writing is completed, you need to press RST to reset**.
-
-### Use Web Flasher
-
-- [ESP Web Flasher Online](https://espressif.github.io/esptool-js/)
-
-![web_flasher](../images/web_flasher.gif)
-
-* **Note that after writing is completed, you need to press RST to reset**.
-
-### Use command line
-
-
-If system asks about install Developer Tools, do it.
-
-```
-python3 -m pip install --upgrade pip
-python3 -m pip install esptool
-```
-
-In order to launch esptool.py, exec directly with this:
-
-```
-python3 -m esptool
-```
-
-For ESP32 use the following command to write
-
-```
-esptool --chip esp32  --baud 921600 --before default_reset --after hard_reset write_flash -z --flash_mode dio --flash_freq 80m 0x0 firmware.bin
-
-```
-
-
-For ESP32-S3 use the following command to write
-
-```
-esptool --chip esp32s3  --baud 921600 --before default_reset --after hard_reset write_flash -z --flash_mode dio --flash_freq 80m 0x0 firmware.bin
-
-```
 
+   
 ## How to check GPS data ?
 
 1. Download [u-center2](https://www.u-blox.com/en/product/u-center)
 2. Check the GPS data according to the guide below
-   ![](../images/u-center2.gif)
+    ![](../images/u-center2.gif)
 
 

firmware/README.MD

@@ -1,41 +1,63 @@
 
 
+## How to Flash ?
+
+
+### Before burning firmware, please put the board into download mode and follow the steps below
+
+ 1. Connect the board via the USB cable
+ 2. Press and hold the **BOOT** button , While still pressing the **BOOT** button (If there is no **BOOT** button, you need to use wires to connect **GND** and **IO0** together.)
+ 3. Press **RST** button
+ 4. Release the **RST** button
+ 5. Release the **BOOT** button (If there is no **BOOT** button, disconnect IO0 from GND.)
+ 6. Upload sketch
+ 7. Press the **RST** button to exit download mode
+
+
 
-# Firmware description
+### Use ESP Download Tool
+
+- Download [Flash_download_tool](https://www.espressif.com.cn/sites/default/files/tools/flash_download_tool_3.9.6_0.zip)
+
+![web_flasher](./images/esp_downloader.gif)
+
+* **Note that after writing is completed, you need to press RST to reset**.
+
+### Use Web Flasher
+
+- [ESP Web Flasher Online](https://espressif.github.io/esptool-js/)
+
+![web_flasher](./images/web_flasher.gif)
+
+* **Note that after writing is completed, you need to press RST to reset**.
+
+### Use command line
+
+
+If system asks about install Developer Tools, do it.
+
+```
+python3 -m pip install --upgrade pip
+python3 -m pip install esptool
+```
+
+In order to launch esptool.py, exec directly with this:
+
+```
+python3 -m esptool
+```
+
+For ESP32 use the following command to write
+
+```
+esptool --chip esp32  --baud 921600 --before default_reset --after hard_reset write_flash -z --flash_mode dio --flash_freq 80m 0x0 firmware.bin
 
 ```
 
-├─GPS_ reset_test       # GPS reset procedure for t-beam-v1.x
+
-├─NMEA_Reset            # GPS reset procedure for t-beam-v1.x
+For ESP32-S3 use the following command to write
-├─T3_SleepTest
-├─LORA_C6_test          # LORA C6 SX1262       
-├─hardware_test         # Used to detect whether the hardware is normal
-│  ├─H594_LoRaS3_1.0
-│  ├─lora32_v1.0_433
-│  ├─lora32_v1.0_868
-│  ├─lora32_v1.0_915
-│  ├─lora32_v1.3_868
-│  ├─lora32_v1.3_915
-│  ├─lora32_v2.0_433
-│  ├─lora32_v2.0_868
-│  ├─lora32_v2.0_915
-│  ├─lora32_V2.1_433
-│  ├─lora32_V2.1_868
-│  ├─lora32_v2.1_915
-│  ├─lorac6_v1.0_868
-│  ├─t-beam-v1.1
-│  │  ├─SX1262
-│  │  ├─SX1268
-│  │  ├─SX1276
-│  │  └─SX1278
-│  ├─t-beam-v3.0
-│  └─T3_V1.8_2.4G
-└─ 
 
 ```
+esptool --chip esp32s3  --baud 921600 --before default_reset --after hard_reset write_flash -z --flash_mode dio --flash_freq 80m 0x0 firmware.bin
 
-###  To write firmware, please check the corresponding link below
+```
-
-[Flash firmware in Mac OS](https://github.com/Xinyuan-LilyGO/LilyGo-Document/blob/master/MacFlashBin.md)
-
-[Flash firmware in windows](https://github.com/Xinyuan-LilyGO/LilyGo-Document/blob/master/WinFlashBin.md)

firmware/T3_SleepTest/README.MD

@@ -1,5 +0,0 @@
-1. Tool download  [flash_download_tool](https://www.espressif.com/sites/default/files/tools/flash_download_tool_v3.8.5.zip)
-
-2. Set according to the picture 
-
-    ![](./SETTING.png)