#pragma once

/*
* This sample program only supports SX1262
* */
// #define LILYGO_TBeam_V0_7
// #define LILYGO_TBeam_V1_X
// #define LILYGO_TBeamS3_SUPREME_V3_0
// #define LILYGO_T3_V1_0
// #define LILYGO_T3_V1_3
// #define LILYGO_T3_V1_6
// #define LILYGO_T3_V2_0
// #define LILYGO_T3_S3_V1_0
/*
* The default program uses 868MHz,
* if you need to change it,
* please open this note and change to the frequency you need to test
* */

#ifndef LoRa_frequency
#define LoRa_frequency      868.0
#endif


#define UNUSE_PIN                   (0)

#if defined(LILYGO_TBeam_V0_7)
#define GPS_RX_PIN                  12
#define GPS_TX_PIN                  15
#define BUTTON_PIN                  39
#define BUTTON_PIN_MASK             GPIO_SEL_39
#define I2C_SDA                     21
#define I2C_SCL                     22

#define RADIO_SCLK_PIN               5
#define RADIO_MISO_PIN              19
#define RADIO_MOSI_PIN              27
#define RADIO_CS_PIN                18
#define RADIO_DIO0_PIN               26
#define RADIO_RST_PIN               23
#define RADIO_DIO1_PIN              33
#define RADIO_BUSY_PIN              32

#define BOARD_LED                   14
#define LED_ON                      HIGH
#define LED_OFF                     LOW

#define GPS_BAUD_RATE               9600
#define HAS_GPS
#define HAS_DISPLAY                 //Optional, bring your own board, no OLED !!

#elif defined(LILYGO_TBeam_V1_X)

#define GPS_RX_PIN                  34
#define GPS_TX_PIN                  12
#define BUTTON_PIN                  38
#define BUTTON_PIN_MASK             GPIO_SEL_38
#define I2C_SDA                     21
#define I2C_SCL                     22
#define PMU_IRQ                     35

#define RADIO_SCLK_PIN               5
#define RADIO_MISO_PIN              19
#define RADIO_MOSI_PIN              27
#define RADIO_CS_PIN                18
#define RADIO_DIO0_PIN               26
#define RADIO_RST_PIN               23
#define RADIO_DIO1_PIN              33
#define RADIO_BUSY_PIN              32

#define BOARD_LED                   4
#define LED_ON                      LOW
#define LED_OFF                     HIGH

#define GPS_BAUD_RATE               9600
#define HAS_GPS
#define HAS_DISPLAY                 //Optional, bring your own board, no OLED !!
#define HAS_PMU


#elif defined(LILYGO_TBeamS3_SUPREME_V3_0)

#define I2C_SDA                    17
#define I2C_SCL                    18

#define I2C1_SDA                    42
#define I2C1_SCL                    41
#define PMU_IRQ                     40

#define GPS_RX_PIN                  9
#define GPS_TX_PIN                  8
#define GPS_WAKEUP_PIN              7
#define GPS_1PPS_PIN                6

#define BUTTON_PIN                  0
#define BUTTON_PIN_MASK             GPIO_SEL_0
#define BUTTON_CONUT                (1)
#define BUTTON_ARRAY                {BUTTON_PIN}

#define RADIO_SCLK_PIN              (12)
#define RADIO_MISO_PIN              (13)
#define RADIO_MOSI_PIN              (11)
#define RADIO_CS_PIN                (10)
#define RADIO_DIO0_PIN               (-1)
#define RADIO_RST_PIN               (5)
#define RADIO_DIO1_PIN              (1)
#define RADIO_BUSY_PIN              (4)

#define SPI_MOSI                    (35)
#define SPI_SCK                     (36)
#define SPI_MISO                    (37)
#define SPI_CS                      (47)
#define IMU_CS                      (34)
#define IMU_INT                     (33)

#define SDCARD_MOSI                 SPI_MOSI
#define SDCARD_MISO                 SPI_MISO
#define SDCARD_SCLK                 SPI_SCK
#define SDCARD_CS                   SPI_CS

#define PIN_NONE                    (-1)
#define RTC_INT                     (14)

#define GPS_BAUD_RATE               9600

#define HAS_SDCARD
#define HAS_GPS
#define HAS_DISPLAY
#define HAS_PMU

#define __HAS_SPI1__
#define __HAS_SENSOR__

#define PMU_WIRE_PORT   Wire1
#define DISPLAY_MODEL   U8G2_SH1106_128X64_NONAME_F_HW_I2C

#elif defined(LILYGO_T3_V1_0)
#define I2C_SDA                     4
#define I2C_SCL                     15
#define OLED_RST                    16

#define RADIO_SCLK_PIN              5
#define RADIO_MISO_PIN              19
#define RADIO_MOSI_PIN              27
#define RADIO_CS_PIN                18
#define RADIO_DIO0_PIN               26
#define RADIO_RST_PIN               14
#define RADIO_DIO1_PIN              33
#define RADIO_BUSY_PIN              32

#define HAS_DISPLAY

#elif defined(LILYGO_T3_V1_3)

#define I2C_SDA                     21
#define I2C_SCL                     22
#define OLED_RST                    UNUSE_PIN

#define RADIO_SCLK_PIN              5
#define RADIO_MISO_PIN              19
#define RADIO_MOSI_PIN              27
#define RADIO_CS_PIN                18
#define RADIO_DIO0_PIN               26
#define RADIO_RST_PIN               14
#define RADIO_DIO1_PIN              33
#define RADIO_BUSY_PIN              32

#define ADC_PIN                     35

#define HAS_DISPLAY
#elif defined(LILYGO_T3_V1_6)
#define I2C_SDA                     21
#define I2C_SCL                     22
#define OLED_RST                    UNUSE_PIN

#define RADIO_SCLK_PIN              5
#define RADIO_MISO_PIN              19
#define RADIO_MOSI_PIN              27
#define RADIO_CS_PIN                18
#define RADIO_DIO0_PIN               26
#define RADIO_RST_PIN               23
#define RADIO_DIO1_PIN              33
#define RADIO_BUSY_PIN              32

#define SDCARD_MOSI                 15
#define SDCARD_MISO                 2
#define SDCARD_SCLK                 14
#define SDCARD_CS                   13

#define BOARD_LED                   25
#define LED_ON                      HIGH

#define ADC_PIN                     35

#define HAS_SDCARD
#define HAS_DISPLAY

#elif defined(LILYGO_T3_V2_0)
#define I2C_SDA                     21
#define I2C_SCL                     22
#define OLED_RST                    UNUSE_PIN

#define RADIO_SCLK_PIN              5
#define RADIO_MISO_PIN              19
#define RADIO_MOSI_PIN              27
#define RADIO_CS_PIN                18
#define RADIO_DIO0_PIN               26
#define RADIO_RST_PIN               14
#define RADIO_DIO1_PIN              UNUSE_PIN
#define RADIO_BUSY_PIN              UNUSE_PIN

#define SDCARD_MOSI                 15
#define SDCARD_MISO                 2
#define SDCARD_SCLK                 14
#define SDCARD_CS                   13

#define BOARD_LED                   0
#define LED_ON                      LOW

#define HAS_DISPLAY
#define HAS_SDCARD


#elif defined(LILYGO_T3_S3_V1_0) || defined(LILYGO_T3_S3_V1_2)

#define I2C_SDA                     18
#define I2C_SCL                     17
#define OLED_RST                    UNUSE_PIN

#define RADIO_SCLK_PIN              5
#define RADIO_MISO_PIN              3
#define RADIO_MOSI_PIN              6
#define RADIO_CS_PIN                7
#define RADIO_DIO1_PIN              33
#define RADIO_BUSY_PIN              34
#define RADIO_RST_PIN               8

//!SX1276/78 module only
#define RADIO_DIO0_PIN              9
#define RADIO_DIO3_PIN              21
#define RADIO_DIO4_PIN              10
#define RADIO_DIO5_PIN              36
//! end

#define SDCARD_MOSI                 11
#define SDCARD_MISO                 2
#define SDCARD_SCLK                 14
#define SDCARD_CS                   13

#define BOARD_LED                   37
#define LED_ON                      HIGH

#define BAT_ADC_PIN                1
#define BUTTON_PIN                 0

#define HAS_SDCARD
#define HAS_DISPLAY


#else
#error "For the first use, please define the board version and model in <utilities. h>"
#endif