clean up

README.md

@@ -1,3 +1,259 @@
-# motion-diagnostics-suite
+# sv06-belt-recovery-stress-tests
 
-Parametric OpenSCAD models and procedures for diagnosing layer shifts, belt tension, and motion instability in FDM 3D printers.
+Belt tension recovery and motion stability test models for bed-slinger 3D printers (e.g., SV06-class machines).
+
+---
+![](img/DSC_5098.webp)
+## Purpose
+
+These models are designed to help recover from situations where printer motion accuracy has been degraded, typically due to:
+
+* Adjusting belt tension without a reference baseline
+* Experiencing layer shifts during prints
+* Replacing belts or modifying mechanical components
+
+This project provides:
+
+* Parametric OpenSCAD models
+* A structured test procedure
+* Guidance for interpreting failure modes
+
+---
+
+## When To Use This
+
+Use these tests if you observe:
+
+* Sudden layer shifts (e.g., 3-5 mm offsets)
+* Inconsistent dimensional accuracy
+* Audible belt skipping or motor stutter
+* After adjusting belt tensioners
+
+Here's an example of a case for a hand held radio where the top suddendly shift at the 20mm height.
+![](img/20260318_215156_Wed.png)
+---
+
+## Models Included
+
+### 1. Cube (Baseline Test)
+
+* Dimensions: 40 × 40 × 40 mm
+* Purpose:
+
+  * Verify basic printer stability
+  * Detect gross mechanical issues
+
+---
+
+### 2. Y-Bar (Axis Stress Test)
+
+* Dimensions: 20 × 150 × 50 mm
+* Purpose:
+
+  * Stress the Y-axis (bed movement)
+  * Detect belt slip under momentum and direction reversal
+
+**Important:**
+
+* Orient the 150 mm dimension front-to-back on the bed
+
+---
+
+### 3. Tower (Long-Duration Test)
+
+* Dimensions: 18 × 18 × 120 mm
+* Purpose:
+
+  * Reveal issues that appear only over time
+  * Detect cumulative drift, resonance, or late-stage layer shifts
+
+---
+
+## Print Procedure (Recommended Order)
+
+Run each model as a **separate print job**:
+
+1. **Cube**
+
+   * Confirms system is not fundamentally broken
+
+2. **Y-Bar**
+
+   * Directly tests axis tension and inertia behavior
+
+3. **Tower**
+
+   * Tests stability over time and height
+
+---
+
+## Suggested Slicer Settings (Orca Slicer)
+
+### Cube
+
+* Layer height: 0.20 mm
+* Perimeters: 3
+* Infill: 20-25% (grid or gyroid)
+
+### Y-Bar
+
+* Layer height: 0.20 mm
+* Perimeters: 3
+* Infill: 15-25% (grid recommended)
+
+### Tower
+
+* Layer height: 0.20 mm
+* Perimeters: 3
+* Infill: 0-10%
+* Brim: optional (only if adhesion is an issue)
+
+See the settings folder for settings used in Orca Slicer.
+
+---
+
+## Belt Tension Guidance
+
+This project assumes GT2 belts (typical for most hobby printers).
+
+### Frequency Method (Recommended)
+
+Using a phone-based spectrum analyzer:
+
+* Target range: **90-110 Hz**
+* Reference: ~110 Hz ? ~2 lb tension (Voron baseline)
+
+Procedure:
+
+1. Move bed so belt span ~ 150 mm
+2. Pluck belt
+3. Measure frequency
+4. Adjust tensioner
+5. Repeat until stable
+
+### Notes
+
+* Too loose:
+
+  * Low frequency (<70 Hz)
+  * Layer shifts likely
+
+* Too tight:
+
+  * High frequency (>120-130 Hz)
+  * Motor strain, possible missed steps
+
+---
+
+## Interpreting Results
+
+### Good Result
+
+* Clean vertical alignment
+* No sudden offsets
+* Consistent layer stacking
+
+---
+
+### Failure Modes
+
+#### Sudden Layer Shift
+
+* Cause:
+
+  * Belt too loose
+  * Pulley slipping
+* Action:
+
+  * Increase tension slightly
+  * Check motor pulley set screws
+
+---
+
+#### Repeated Shift at Same Height
+
+* Cause:
+
+  * Mechanical obstruction
+  * Cable snag
+* Action:
+
+  * Inspect motion path
+  * Check wiring harness clearance
+
+---
+
+#### Gradual Lean / Drift
+
+* Cause:
+
+  * Frame or axis alignment issue
+* Action:
+
+  * Inspect rails, wheels, or rods
+
+---
+
+#### Ringing / Ghosting (No Shift)
+
+* Cause:
+
+  * High acceleration
+* Action:
+
+  * Reduce acceleration (not a belt issue)
+
+---
+
+## Notes on Methodology
+
+These tests intentionally:
+
+* Emphasize repeated motion in one axis
+* Increase inertial load with height
+* Create conditions where marginal tension fails visibly
+
+This approach isolates motion system issues rather than general print quality.
+
+---
+
+## OpenSCAD Usage
+
+Generate models:
+
+```bash
+openscad -D 'model="cube"'  -o cube_$(date +%Y%m%d_%H%M).stl  stress_test_models.scad
+openscad -D 'model="ybar"'  -o ybar_$(date +%Y%m%d_%H%M).stl  stress_test_models.scad
+openscad -D 'model="tower"' -o tower_$(date +%Y%m%d_%H%M).stl stress_test_models.scad
+```
+
+---
+
+## Provenance
+
+Generated with:
+
+* OpenSCAD
+* Orca Slicer (recommended)
+* Frequency-based belt tuning derived from:
+
+  * Voron Design tuning methodology
+
+This project was developed with ChatGPT.
+---
+
+## License
+
+Recommend: MIT or CC-BY 4.0 for broad reuse.
+
+---
+
+## Contributing
+
+Improvements welcome:
+
+* Additional test geometries
+* Axis-specific stress models
+* Automated calibration workflows
+
+---

openscad/stress_test_models.scad

@@ -147,8 +147,48 @@ module rounded_box_uncentered(x, y, z, r) {
                 square([x, y], center=false);
 }
 
-
 module place_top_label(txt, x, y, z, center_it=false) {
+
+    // --- parameters ---
+    margin = 2;  // mm clearance from edges
+
+    // usable space
+    usable_x = x - margin;
+    usable_y = y - margin;
+
+    // choose orientation: run along long axis
+    rotate_text = (y > x);
+
+    // limiting width after orientation
+    limit = rotate_text ? usable_y : usable_x;
+
+    // crude text width estimate factor (~0.6 * size * chars)
+    est_char_width = 1.0;
+    est_len = len(txt) * est_char_width;
+
+    // compute size that fits
+    auto_size = limit / est_len;
+
+    // clamp to your preferred max size
+    final_size = min(label_size, auto_size);
+
+    // placement
+    tx = center_it ? 0 : x/2;
+    ty = center_it ? 0 : y/2;
+    tz = center_it ? z/2 : z;
+
+    translate([tx, ty, tz - label_depth])
+        rotate([0, 0, rotate_text ? 90 : 0])
+            linear_extrude(height=label_depth + 0.02)
+                text(
+                    txt,
+                    size=final_size,
+                    font=label_font,
+                    halign="center",
+                    valign="center"
+                );
+}
+module place_top_labelOLD(txt, x, y, z, center_it=false) {
     tx = center_it ? 0 : x/2;
     ty = center_it ? 0 : y/2;
     tz = center_it ? z/2 : z;

openscad/stress_test_models.scad~

@@ -1,166 +0,0 @@
-#!/usr/bin/openscad -o /tmp/ignore.stl
-//
-// stress_test_models.scad
-// 20260317 ChatGPT
-// $Id$
-// $HeadURL$
-//
-// Example command lines:
-//
-//   openscad -D 'model="cube"'  -o cube_20260317_1335.stl  stress_test_models.scad
-//   openscad -D 'model="ybar"'  -o ybar_20260317_1335.stl  stress_test_models.scad
-//   openscad -D 'model="tower"' -o tower_20260317_1335.stl stress_test_models.scad
-//   openscad -D 'model="all"'   -o all_20260317_1335.stl   stress_test_models.scad
-//
-// Suggested slicer use:
-//
-//   1) Print each model as a SEPARATE run.
-//   2) For ybar, orient the LONG dimension along the printer's Y axis
-//      so the bed moves the long way front-to-back.
-//   3) Infill is set in Orca Slicer, not here.
-//
-// Suggested slicer settings:
-//
-//   cube:  0.20 layer, 3 perimeters, 20-25% grid or gyroid
-//   ybar:  0.20 layer, 3 perimeters, 15-25% grid
-//   tower: 0.20 layer, 3 perimeters, 0-10% infill, no brim at first;
-//          add brim only if adhesion becomes the issue rather than motion
-//
-
-/* [General] */
-model = "all";              // [cube,ybar,tower,all]
-center_models = false;      // true / false
-add_labels = true;          // true / false
-
-/* [Cube Dimensions] */
-cube_x = 40;
-cube_y = 40;
-cube_z = 40;
-
-/* [Y Bar Dimensions] */
-ybar_x = 20;
-ybar_y = 150;
-ybar_z = 50;
-
-/* [Tower Dimensions] */
-tower_x = 18;
-tower_y = 18;
-tower_z = 120;
-
-/* [Edge Treatment] */
-corner_radius = 1.2;        // 0 for sharp corners
-$fn = 48;
-
-/* [Labeling] */
-label_depth = 0.6;
-label_size  = 7;
-label_font  = "Liberation Sans:style=Bold";
-
-/* [Layout For model="all"] */
-gap_between_models = 20;
-
-
-// --------------------------------------------------
-// Main
-// --------------------------------------------------
-
-if (model == "cube") {
-    make_cube();
-}
-else if (model == "ybar") {
-    make_ybar();
-}
-else if (model == "tower") {
-    make_tower();
-}
-else if (model == "all") {
-    make_all();
-}
-else {
-    echo("ERROR: model must be one of: cube, ybar, tower, all");
-}
-
-
-// --------------------------------------------------
-// Assemblies
-// --------------------------------------------------
-
-module make_all() {
-    x0 = 0;
-    x1 = x0 + cube_x + gap_between_models;
-    x2 = x1 + ybar_x + gap_between_models;
-
-    translate([x0, 0, 0]) make_cube();
-    translate([x1, 0, 0]) make_ybar();
-    translate([x2, 0, 0]) make_tower();
-}
-
-
-module make_cube() {
-    difference() {
-        rounded_box(cube_x, cube_y, cube_z, corner_radius, center_models);
-        if (add_labels)
-            place_top_label("CUBE", cube_x, cube_y, cube_z, center_models);
-    }
-}
-
-
-module make_ybar() {
-    difference() {
-        rounded_box(ybar_x, ybar_y, ybar_z, corner_radius, center_models);
-        if (add_labels)
-            place_top_label("YBAR", ybar_x, ybar_y, ybar_z, center_models);
-    }
-}
-
-
-module make_tower() {
-    difference() {
-        rounded_box(tower_x, tower_y, tower_z, corner_radius, center_models);
-        if (add_labels)
-            place_top_label("TOWER", tower_x, tower_y, tower_z, center_models);
-    }
-}
-
-
-// --------------------------------------------------
-// Geometry helpers
-// --------------------------------------------------
-
-module rounded_box(x, y, z, r=0, center_it=false) {
-    if (r <= 0) {
-        cube([x, y, z], center=center_it);
-    } else {
-        if (center_it) {
-            translate([-x/2, -y/2, -z/2])
-                rounded_box_uncentered(x, y, z, r);
-        } else {
-            rounded_box_uncentered(x, y, z, r);
-        }
-    }
-}
-
-
-module rounded_box_uncentered(x, y, z, r) {
-    linear_extrude(height=z)
-        offset(r=r)
-            offset(delta=-r)
-                square([x, y], center=false);
-}
-
-
-module place_top_label(txt, x, y, z, center_it=false) {
-    tx = center_it ? 0 : x/2;
-    ty = center_it ? 0 : y/2;
-    tz = center_it ? z/2 : z;
-
-    translate([tx, ty, tz - label_depth])
-        linear_extrude(height=label_depth + 0.02)
-            text(
-                txt,
-                size=label_size,
-                font=label_font,
-                halign="center",
-                valign="center"
-            );
-}

orca-slicer/settings/PolyLite PLA @System - Z-Tower.info

@@ -0,0 +1,5 @@
+sync_info = create
+user_id = 
+setting_id = 
+base_id = OGFSL19
+updated_time = 0

orca-slicer/settings/PolyLite PLA @System - Z-Tower.json

@@ -0,0 +1,16 @@
+{
+    "compatible_printers": [
+        "Sovol SV06 ACE 0.4 nozzle"
+    ],
+    "fan_cooling_layer_time": [
+        "20"
+    ],
+    "filament_settings_id": [
+        "PolyLite PLA @System - Z-Tower"
+    ],
+    "from": "User",
+    "inherits": "PolyLite PLA @System",
+    "is_custom_defined": "0",
+    "name": "PolyLite PLA @System - Z-Tower",
+    "version": "2.3.0.3"
+}

orca-slicer/settings/Y-bar_20260317_final.info

@@ -0,0 +1,5 @@
+sync_info = update
+user_id = 
+setting_id = 
+base_id = GP004
+updated_time = 0

orca-slicer/settings/Y-bar_20260317_final.json

@@ -0,0 +1,24 @@
+{
+    "bottom_shell_layers": "5",
+    "brim_type": "outer_only",
+    "from": "User",
+    "inherits": "0.20mm Standard @Sovol SV06 ACE",
+    "initial_layer_line_width": "0.42",
+    "initial_layer_print_height": "0.2",
+    "inner_wall_speed": "80",
+    "is_custom_defined": "0",
+    "line_width": "0.42",
+    "name": "Y-bar_20260317_final",
+    "only_one_wall_top": "0",
+    "outer_wall_acceleration": "1500",
+    "outer_wall_line_width": "0.42",
+    "outer_wall_speed": "60",
+    "print_settings_id": "Y-bar_20260317_final",
+    "skirt_loops": "2",
+    "sparse_infill_density": "20%",
+    "sparse_infill_pattern": "gyroid",
+    "top_shell_layers": "5",
+    "top_solid_infill_flow_ratio": "1",
+    "version": "2.3.0.3",
+    "wall_loops": "3"
+}

orca-slicer/settings/Z-tower_20260317_final.info

@@ -0,0 +1,5 @@
+sync_info = update
+user_id = 
+setting_id = 
+base_id = GP004
+updated_time = 0

orca-slicer/settings/Z-tower_20260317_final.json

@@ -0,0 +1,26 @@
+{
+    "bottom_shell_layers": "5",
+    "brim_type": "outer_only",
+    "from": "User",
+    "inherits": "0.20mm Standard @Sovol SV06 ACE",
+    "initial_layer_line_width": "0.42",
+    "initial_layer_print_height": "0.2",
+    "inner_wall_speed": "80",
+    "is_custom_defined": "0",
+    "line_width": "0.42",
+    "name": "Z-tower_20260317_final",
+    "notes": "Orca serialization note\n\nIn Orca Slicer 2.3.0.3, some live profile values may not appear in the saved process JSON even when they are active in the UI. For the Z-tower profile, Sparse infill density was verified in the live UI as 10% before slicing, even though the saved JSON did not include a sparse_infill_density key.\n\nScreenshot was taken showing the 10% value, 20260318_184351_Wed.png",
+    "only_one_wall_top": "0",
+    "outer_wall_acceleration": "1500",
+    "outer_wall_line_width": "0.42",
+    "outer_wall_speed": "40",
+    "print_settings_id": "Z-tower_20260317_final",
+    "seam_gap": "0",
+    "seam_position": "back",
+    "skirt_loops": "2",
+    "sparse_infill_pattern": "line",
+    "top_shell_layers": "5",
+    "top_solid_infill_flow_ratio": "1",
+    "version": "2.3.0.3",
+    "wall_loops": "3"
+}

orca-slicer/settings/cube_20260317_final.info

@@ -0,0 +1,5 @@
+sync_info = create
+user_id = 
+setting_id = 
+base_id = GP004
+updated_time = 0

orca-slicer/settings/cube_20260317_final.json

@@ -0,0 +1,23 @@
+{
+    "bottom_shell_layers": "5",
+    "brim_type": "no_brim",
+    "from": "User",
+    "inherits": "0.20mm Standard @Sovol SV06 ACE",
+    "initial_layer_line_width": "0.42",
+    "initial_layer_print_height": "0.2",
+    "inner_wall_speed": "80",
+    "is_custom_defined": "0",
+    "line_width": "0.42",
+    "name": "cube_20260317_final",
+    "only_one_wall_top": "0",
+    "outer_wall_acceleration": "1500",
+    "outer_wall_line_width": "0.42",
+    "outer_wall_speed": "60",
+    "print_settings_id": "cube_20260317_final",
+    "seam_position": "back",
+    "skirt_loops": "2",
+    "sparse_infill_pattern": "grid",
+    "top_shell_layers": "5",
+    "top_solid_infill_flow_ratio": "1",
+    "version": "2.3.0.3"
+}