LilyGo-LoRa-Series/examples/LoRaWAN/OTTA/utilities.h

#pragma once

// #define LILYGO_TBeam_V0_7
// #define LILYGO_TBeam_V1_X
// #define LILYGO_T3_V1_0
// #define LILYGO_T3_V1_3
// #define LILYGO_T3_V1_6
// #define LILYGO_T3_V2_0
// #define LILYGO_T_MOTION_S76G

// #define LILYGO_T_MOTION_S78G         //Not support
/*
* The default LMIC_Arduino uses the 868MHz configuration,
* you need to change the frequency,
* please go to LMIC-Arduino/src/lmic/config.h to change
* */
// LMIC-Arduino/src/lmic/config.h


#define UNUSE_PIN                   (0)

#if defined(LILYGO_TBeam_V0_7)
#define GPS_RX_PIN                  12
#define GPS_TX_PIN                  15
#define BUTTON_PIN                  39
#define BUTTON_PIN_MASK             GPIO_SEL_39
#define I2C_SDA                     21
#define I2C_SCL                     22

#define RADIO_SCLK_PIN               5
#define RADIO_MISO_PIN              19
#define RADIO_MOSI_PIN              27
#define RADIO_CS_PIN                18
#define RADIO_DIO0_PIN               26
#define RADIO_RST_PIN               23
#define RADIO_DIO1_PIN              33
#define RADIO_BUSY_PIN              32

#define BOARD_LED                   14
#define LED_ON                      HIGH
#define LED_OFF                     LOW

#define GPS_BAUD_RATE               9600
#define HAS_GPS
#define HAS_DISPLAY                 //Optional, bring your own board, no OLED !!

#elif defined(LILYGO_TBeam_V1_X)

#define GPS_RX_PIN                  34
#define GPS_TX_PIN                  12
#define BUTTON_PIN                  38
#define BUTTON_PIN_MASK             GPIO_SEL_38
#define I2C_SDA                     21
#define I2C_SCL                     22
#define PMU_IRQ                     35

#define RADIO_SCLK_PIN               5
#define RADIO_MISO_PIN              19
#define RADIO_MOSI_PIN              27
#define RADIO_CS_PIN                18
#define RADIO_DIO0_PIN               26
#define RADIO_RST_PIN               23
#define RADIO_DIO1_PIN              33
#define RADIO_BUSY_PIN              32

#define BOARD_LED                   4
#define LED_ON                      LOW
#define LED_OFF                     HIGH

#define GPS_BAUD_RATE               9600
#define HAS_GPS
#define HAS_DISPLAY                 //Optional, bring your own board, no OLED !!

#elif defined(LILYGO_T3_V1_0)
#define I2C_SDA                     4
#define I2C_SCL                     15
#define OLED_RST                    16

#define RADIO_SCLK_PIN              5
#define RADIO_MISO_PIN              19
#define RADIO_MOSI_PIN              27
#define RADIO_CS_PIN                18
#define RADIO_DIO0_PIN               26
#define RADIO_RST_PIN               14
#define RADIO_DIO1_PIN              33
#define RADIO_BUSY_PIN              32

#define HAS_DISPLAY


#elif defined(LILYGO_T3_V1_3)

#define I2C_SDA                     21
#define I2C_SCL                     22
#define OLED_RST                    UNUSE_PIN

#define RADIO_SCLK_PIN              5
#define RADIO_MISO_PIN              19
#define RADIO_MOSI_PIN              27
#define RADIO_CS_PIN                18
#define RADIO_DIO0_PIN               26
#define RADIO_RST_PIN               14
#define RADIO_DIO1_PIN              33
#define RADIO_BUSY_PIN              32

#define ADC_PIN                     35

#define HAS_DISPLAY

#elif defined(LILYGO_T3_V1_6)
#define I2C_SDA                     21
#define I2C_SCL                     22
#define OLED_RST                    UNUSE_PIN

#define RADIO_SCLK_PIN              5
#define RADIO_MISO_PIN              19
#define RADIO_MOSI_PIN              27
#define RADIO_CS_PIN                18
#define RADIO_DIO0_PIN               26
#define RADIO_RST_PIN               23
#define RADIO_DIO1_PIN              33
#define RADIO_BUSY_PIN              32

#define SDCARD_MOSI                 15
#define SDCARD_MISO                 2
#define SDCARD_SCLK                 14
#define SDCARD_CS                   13

#define BOARD_LED                   25
#define LED_ON                      HIGH

#define ADC_PIN                     35

#define HAS_SDCARD
#define HAS_DISPLAY


#elif defined(LILYGO_T3_V1_6_TXCO)


#define I2C_SDA                     21
#define I2C_SCL                     22
#define OLED_RST                    UNUSE_PIN

#define RADIO_SCLK_PIN              5
#define RADIO_MISO_PIN              19
#define RADIO_MOSI_PIN              27
#define RADIO_CS_PIN                18
#define RADIO_DIO0_PIN              26
#define RADIO_RST_PIN               23
// #define RADIO_DIO1_PIN              33
/*
* In the T3 V1.6.1 TXCO version, Radio DIO1 is connected to Radio’s
* internal temperature-compensated crystal oscillator enable
* */
#define RADIO_TXCO_ENABLE           33
#define RADIO_BUSY_PIN              32

#define SDCARD_MOSI                 15
#define SDCARD_MISO                 2
#define SDCARD_SCLK                 14
#define SDCARD_CS                   13

#define BOARD_LED                   25
#define LED_ON                      HIGH

#define ADC_PIN                     35

#define HAS_SDCARD
#define HAS_DISPLAY


#elif defined(LILYGO_T3_V2_0)
#define I2C_SDA                     21
#define I2C_SCL                     22
#define OLED_RST                    UNUSE_PIN

#define RADIO_SCLK_PIN              5
#define RADIO_MISO_PIN              19
#define RADIO_MOSI_PIN              27
#define RADIO_CS_PIN                18
#define RADIO_DIO0_PIN               26
#define RADIO_RST_PIN               14
#define RADIO_DIO1_PIN              UNUSE_PIN
#define RADIO_BUSY_PIN              UNUSE_PIN

#define SDCARD_MOSI                 15
#define SDCARD_MISO                 2
#define SDCARD_SCLK                 14
#define SDCARD_CS                   13

#define BOARD_LED                   0
#define LED_ON                      LOW

#define HAS_DISPLAY
#define HAS_SDCARD

#elif defined(LILYGO_T_MOTION_S76G)
#define RADIO_SCLK_PIN                                  PB13
#define RADIO_MISO_PIN                                  PB14
#define RADIO_MOSI_PIN                                  PB15
#define RADIO_CS_PIN                                    PB12
#define RADIO_RST_PIN                                   PB10

#define RADIO_DIO0_PIN                                  PB11
#define RADIO_DIO1_PIN                                  PC13
#define RADIO_DIO2_PIN                                  PB9
#define RADIO_DIO3_PIN                                  PB4
#define RADIO_DIO4_PIN                                  PB3
#define RADIO_DIO5_PIN                                  PA15

#define RADIO_SWITCH_PIN                                PA1 //1:Rx, 0:Tx

#define GPS_RST_PIN                                     PB2
#define GPS_RX_PIN                                      PC11
#define GPS_TX_PIN                                      PC10
#define GPS_ENABLE_PIN                                  PC6
#define GPS_BAUD_RATE                                   115200
#define GPS_1PPS_PIN                                    PB5

#define UART_RX_PIN                                     PA10
#define UART_TX_PIN                                     PA9

#define HAS_GPS

#else
#error "For the first use, please define the board version and model in <utilities. h>"
#endif